Anonim

Renault Logan

Стоимость комплекта передних колодок: 550-820 руб., задних - 640-1200 руб. The cost of a set of front pads: 550–820 rubles., Rear - 640–1200 rubles. The cost of a set of front pads: 550–820 rubles., Rear - 640–1200 rubles.

Replacing the front brake pads

We replace the pads in the case of the maximum allowable wear of their pads - the minimum thickness of the pads, including its base, must be at least 6 mm. You should also update the pads when replacing the brake disc, oiling the pads or the presence of deep grooves, cracks and chips on them. If the fluid level in the tank of the hydraulic brake actuator is at MAX, then before installing new pads with a syringe or rubber bulb, we pump out part of the fluid from the tank. Remove the front wheel. Before installing new pads, it is necessary to move the piston of the wheel cylinder to the inside of the cylinder as much as possible. To do this, by inserting a screwdriver with a wide blade through the hole in the caliper between the base of the outer block and the caliper and leaning it on the caliper …

one

…сдвигаем скобу, утапливая поршень в цилиндр. … we shift the bracket, recessing the piston into the cylinder. … we shift the bracket, recessing the piston into the cylinder.

2

Накидным ключом «на 13» отворачиваем болт крепления скобы к нижнему направляющему пальцу, удерживая палец рожковым ключом «на 17». Using a “13” ring wrench, unscrew the bracket fastening bolt to the lower guide pin while holding the finger with the “17” open end wrench. Using a “13” ring wrench, unscrew the bracket fastening bolt to the lower guide pin while holding the finger with the “17” open end wrench.

3

Подняв скобу… Holding up the bracket … Holding up the bracket …

four

…вынимаем тормозные колодки из их направляющей. … remove the brake pads from their guide. … remove the brake pads from their guide.

five

Снимаем две пружинные скобы колодок. Металлической щеткой очищаем от грязи и коррозии посадочные места колодок в их направляющей. Перед установкой новых колодок проверяем состояние защитных чехлов направляющих пальцев. Порванный или потерявший эластичность чехол заменяем. Для этого… We remove two spring brackets pads. Using a wire brush, we clean the dirt and corrosion of the pads in their guide. Before installing new pads, we check the condition of the protective covers of the guide fingers. A torn or loose elastic case is replaceable. To do this … We remove two spring brackets pads. Using a wire brush, we clean the dirt and corrosion of the pads in their guide. Before installing new pads, we check the condition of the protective covers of the guide fingers. A torn or loose elastic case is replaceable. For this…

6

…вынимаем направляющий палец из отверстия направляющей колодки и заменяем чехол. (Для замены чехла верхнего направляющего пальца необходимо отвернуть болт крепления скобы к пальцу и снять скобу с направляющей колодок.) Перед установкой пальца вкладываем немного пластичной смазки в отверстие направляющей колодок… … remove the guide pin from the hole of the guide block and replace the cover. (To replace the cover of the upper guide pin, you must unscrew the bracket fastening bolt to the finger and remove the bracket from the guide block.) Before installing the finger, put a little grease into the hole of the guide block … … remove the guide pin from the hole of the guide block and replace the cover. (To replace the cover of the upper guide pin, it is necessary to unscrew the bracket fastening bolt to the finger and remove the bracket from the block guide.) Before installing the finger, put some grease into the hole of the block guide …

7

…и наносим тонкий слой смазки на поверхность пальца. Устанавливаем новые тормозные колодки в направляющую колодок и опускаем скобу. Если выступающая из колесного цилиндра часть поршня препятствует установке суппорта на тормозные колодки, то поднимаем скобу… … and apply a thin layer of grease on the surface of the finger. Install new brake pads in the pad guide and lower the bracket. If the piston part protruding from the wheel cylinder prevents the caliper from being installed on the brake pads, then we raise the bracket … … and apply a thin layer of grease to the surface of the finger. Install new brake pads in the pad guide and lower the bracket. If the piston part protruding from the wheel cylinder prevents the caliper from installing on the brake pads, then we raise the bracket …

eight

…и раздвижными пассатижами утапливаем поршень в цилиндр. Аналогично заменяем колодки на другой стороне автомобиля. После замены колодок несколько раз нажимаем педаль тормоза для установки зазоров между колодками и дисками. Проверяем уровень жидкости в бачке и при необходимости доводим его до нормы. … and with sliding pliers we heat the piston into the cylinder. Similarly, replace the pads on the other side of the car. After replacing the pads, press the brake pedal several times to set the gaps between the pads and discs. We check the fluid level in the tank and, if necessary, bring it to normal. … and with sliding pliers we heat the piston into the cylinder. Similarly, replace the pads on the other side of the car. After replacing the pads, press the brake pedal several times to set the gaps between the pads and discs. We check the fluid level in the tank and, if necessary, bring it to normal.

On a note

The brake pads of the front wheels must be changed only as a set - all four pieces on both front wheels. The same applies to the rear axle. Replacing the pads of only one brake mechanism can lead to the car being pulled to the side with a sharp slowdown.

Replacing the rear brake pads

We replace the pads in the case of the maximum allowable wear of their pads or the drum of the brake mechanism of the rear wheel. The pads must also be replaced when oiling the pads, the presence of deep grooves and chips on them, or if the pads are peeled off the base of the pads. We show the replacement of the pads on the left rear wheel. Remove the decorative wheel cap.

one

Поддев отверткой, снимаем защитный колпак подшипника ступицы. Prying off with a screwdriver, remove the protective cap of the hub bearing. Prying off with a screwdriver, remove the protective cap of the hub bearing.

2

Головкой «на 30» отворачиваем гайку подшипника ступицы. Снимаем заднее колесо и надежно фиксируем автомобиль на опорной стойке заводского изготовления. Перед снятием барабана тормозного механизма опускаем рычаг стояночного троса до упора - автомобиль должен быть расторможен. Head “30” unscrew the nut of the hub bearing. We remove the rear wheel and securely fix the car on the factory-manufactured support stand. Before removing the brake drum, lower the parking cable lever all the way - the car must be released. Head “30” unscrew the nut of the hub bearing. We remove the rear wheel and securely fix the car on the factory-manufactured support stand. Before removing the brake drum, lower the parking cable lever all the way - the car must be released.

3

Снимаем тормозной барабан в сборе с подшипником. Не нажимайте педаль тормоза после снятия тормозного барабана, так как поршни могут полностью выйти из колесного цилиндра! Очищаем детали тормозного механизма от загрязнений. Пассатижами отсоединяем нижний конец пружины регулятора зазоров от передней колодки… Remove the brake drum assembly with the bearing. Do not depress the brake pedal after removing the brake drum, as the pistons may completely exit the wheel cylinder! We clean the details of the brake mechanism from pollution. With pliers, disconnect the lower end of the clearance adjuster spring from the front shoe … Remove the brake drum assembly with the bearing. Do not depress the brake pedal after removing the brake drum, as the pistons may completely exit the wheel cylinder! We clean the details of the brake mechanism from pollution. With pliers, disconnect the lower end of the gap adjuster spring from the front shoe …

four

…и снимаем пружину. … and remove the spring. … and remove the spring.

five

Снимаем рычаг регулятора зазоров. Remove the clearance adjuster lever. Remove the clearance adjuster lever.

6

Поддев отверткой, выводим из зацепления с задней колодкой крючок верхней стяжной пружины и снимаем пружину. Prying off with a screwdriver, disengage the hook of the upper tension spring from the mesh with the rear shoe and remove the spring. Prying off with a screwdriver, disengage the hook of the upper tension spring from the mesh with the rear shoe and remove the spring.

7

Пассатижами поворачиваем чашку пружины опорной стойки колодки до совмещения паза в чашке с хвостовиком стойки. With pliers, we turn the cup of the spring of the support rack of the block until the groove in the cup is aligned with the shaft of the rack. With pliers, we turn the cup of the spring of the support rack of the block until the groove in the cup is aligned with the shaft of the rack.

eight

Снимаем чашку с пружиной и вынимаем опорную стойку из отверстия щита тормозного механизма. Аналогично снимаем опорную стойку задней колодки. Отводим верхний конец передней колодки от рабочего цилиндра… We remove the cup with the spring and remove the support post from the hole of the shield of the brake mechanism. Similarly, remove the support strut of the rear pads. We remove the upper end of the front shoe from the working cylinder … Remove the cup with the spring and remove the support post from the hole of the brake shield. Similarly, remove the support strut of the rear pads. We divert the upper end of the front pads from the working cylinder …

9

…и вынимаем распорную планку. … and take out the spacer bar. … and take out the spacer bar.

ten

Отцепив нижнюю стяжную пружину, снимаем переднюю тормозную колодку. Снимаем нижнюю стяжную пружину. Having unhooked the lower coupling spring, we remove the front brake shoe. Remove the lower tension spring. Having unhooked the lower coupling spring, we remove the front brake shoe. Remove the lower tension spring.

eleven

Отсоединяем наконечник троса стояночного тормоза от рычага задней колодки и снимаем колодку Disconnect the tip of the parking brake cable from the lever of the rear pad and remove the shoe Disconnect the tip of the parking brake cable from the lever of the rear shoe and remove the shoe

We check the technical condition of the parts and clean them. Before installing new pads, we clean the threads of the spacer tip and ratchet nut and apply a thin layer of grease to the threads. Install the new brake pads on the rear wheel in the reverse order. After mounting the pads, we set the mechanism for automatically adjusting the gap to its original state. To do this, by changing the length of the spacer strip, set the distance between the outer surfaces of the linings of the front and rear pads 202.45 ± 0.25 mm.

12

Штангенциркулем измеряем расстояние между наружными поверхностями накладок передней и задней колодок. Для изменения длины распорной планки… Using a vernier caliper, we measure the distance between the outer surfaces of the front and rear shoe pads. To change the length of the spacer bar … Using a vernier caliper, measure the distance between the outer surfaces of the front and rear shoe pads. To change the length of the spacer bar …

13

…отводим рычаг регулятора от храповой гайки резьбового наконечника планки и отверткой вращаем гайку (резьба правая) … we take away the regulator lever from the ratchet nut of the threaded tip of the strap and rotate the nut with a screwdriver (right-hand thread) … we take the regulator lever from the ratchet nut of the threaded tip of the strap and use a screwdriver to rotate the nut (right-hand thread)